Versatile professional with over a decade of experience in welding, fabrication, mechanical installation, and construction supervision. Skilled in leading teams, executing complex projects, and maintaining high safety standards across diverse industries.
Proficient in MIG welding, blueprint reading, and metal fabrication for industrial, commercial, and marine applications.
Experienced in installing, repairing, and maintaining mechanical systems, including electrical and plumbing components.
Led teams in framing, remodeling, and metal spraying projects, ensuring timely completion and quality standards.
Skilled in installing and programming low voltage systems, utility meters, and PV systems for energy efficiency.
Brycon/Intel
Work installing Roxtec, this platform utilizes silicone water proof compression inserts, this is floor mounted for all pass through , from floor to below ceiling. Install 1 gauge ground wire to below ceiling, using ground clamps. Utilize a scissor lift to go to ceiling to install ground wires to cable trays. Install all unistrut with all thread to ceiling unistrut to hang down, for conduit to lay on for travel across building. Misc service panel installs for tooling machines. Install all 90 degree cable tray corners for long runs. Work in the clean room wiring the FFU fans to 110 electrical boxes. Install com cables to daisy chain FFUs. Run and connect all com cables for all ceiling lights in clean room, running per diagram, all data cables for FFU fans in upper floor, connecting to cable trays that run to data box.
Ryan companies/GOstaff
Run a crew of 5, set up and complete construction of framing, remodels. Prep and sand metal structures, set up airless sprayer guns and spray all hand rails metal staircases and safety poles. Mix all paints for projects. Fix all electrical plate covers or replace. Fix all drywall, from pin holes to foot holes. Paint complete walls if necessary. Set up temporary structures. Maintenance on all conveyors, service or repair equipment in building. Fix or replace clean up, tear down. Install and wire up turnstiles for entrance. Check kitchen utilities for proper operation, make sure all lights are working, replace lights if not working, and or repair. Utilize sky track forklift to load and unload trucks, at shop. Make sure all fixtures are working or replace.
High school diploma
Yes, hello, there is a timer changing out a key system in a vehicle to a push button, but the computer wouldn't accept the new codes, so I had to go online, get numbers, get a hold of a company, get on a laptop, start programming into OBD2, and get this corrected. But I learned it. It wasn't hard. I don't have a problem looking stuff up, and I like doing that. But yeah, it created a problem when I thought I could just switch the from the key to a push button and their computer wouldn't take it. All right, thank you.
Hello, my name is Drewman. I pretty much work on cars all the time in my garage. My son and I have kind of like an automotive repair kind of a side gig we do in our garage. We do a lot of stereos, air horns, changing out electrical parts in cars. I'm pretty much mechanically inclined. I like doing that. And I've done some switching of door locks on key holes, switching them to push buttons. Kind of familiar, but I've never done a locksmith work, but I'd love to get into it. Thank you.
Discover other professionals with similar experience
Operated forklifts, box trucks, and fabrication tools, maintaining safety and operational efficiency.
Denso MFG. of Tennessee
Inspect parts for alternators, clean frames, press in bearings, and stater and rotor. Install top frame and put in press to close up, add resistor, put in through bolts and screw in. Solder in resistor then move it down the line. Certified inspector on test bench. Run all parts and check voltage and resistance.
Southern Cross Corporation/SUN RUN
Drive company vehicle all over southern CA to customers, greet and explain the process, answer any questions, commission new PV systems. Install low voltage utilities meters and reprogram to new meter. Upgrade solar inverters with new cell A and cell B card new 4G antennas for communications. Reprogram through solar edge app, solar to accept new processor card. Working with low voltage and 240 volts for disconnects of systems while replacing Ola inverters.
Porvene Doors
Complete fabrication of schedule 40 pipe barrels. Work from blueprints. Cut, use of lathe, gas cutting, facing of wearable parts and complete welding of barrel assemblies. General welding of assembly parts for barrels. Complete all paperwork for orders, load up doors on box truck, deliver to jobsites and customers warehouses.
Robert Taylor construction
Fabricate all metal frames and gates for commercial properties. Measure all jobs for fabrication, complete all drawings for bids and fabrication. Complete all stock orders for jobs and set up all dates for installs. Weld up customers trailers for tie downs and holding legs for loading. Repair broken trailers, refurb and work as finish installs in remodels. Install ceiling fans, electrical outlets, switches, face plates, door handles, most bathroom hangers, mirrors, most finish work in remodels. Use stale bed truck to deliver all jobs.
CTI Creative Touch Interiors
Cut, grind, laminate granite counter tops. Level out cuts to get laminated, cut and polish on tables. Use diamond polish pads and park, pro edge, and bridge saw. Went to park industries in Minnesota, to get certified.
TI trailers
Fabricate boat trailers from blueprints, weld on production line. Cut all steel on cold saw and drill holes for mounts from specs. Weld up leaf springs to frames, complete all install parts. Pick up steel from steel company and deliver to shop, load and unload material.
